The "bullseye" Raspbian distro should include enough kernel mods to
let the PB-ADV mesh work. Unfortunately, the version of
5.55, which is known to be flaky. You should enable the apt
repo to install at least version
This requires adding a line to
/etc/apt/sources.list and creating a
To do that, run these commands:
# Become root sudo su - # Add the testing repo cat >>/etc/apt/sources.list <<EOF deb http://raspbian.raspberrypi.org/raspbian/ testing main contrib non-free rpi EOF # Prioritize stable packages cat >/etc/apt/preferences.d/prefs <<EOF Package: * Pin: release a=stable Pin-Priority: 700 Package: * Pin: release a=testing Pin-Priority: 650 EOF # Update the list of available packages apt update
To get a working version of
bluez, do the following:
$ sudo apt -t testing install bluez bluez-meshd
Now you’re ready to fire up a BLE mesh. Most of this is based upon the details from the Bluetooth Site
This can be done as non-root regular user.
If it fails silently, ensure you have a
If it complains about a missing
config_db.json file, create one
pi@raspberrypi:~ $ mesh-cfgclient Warning: config file "/home/pi/.config/meshcfg/config_db.json" not found Proxy added: org.bluez.mesh.Network1 (/org/bluez/mesh) [mesh-cfgclient]# create Created new node with token 176b9238fa48857c Proxy added: org.bluez.mesh.Node1 (/org/bluez/mesh/node326d83779e8ccbaf254d4b604dfec674) Proxy added: org.bluez.mesh.Management1 (/org/bluez/mesh/node326d83779e8ccbaf254d4b604dfec674) Attached with path /org/bluez/mesh/node326d83779e8ccbaf254d4b604dfec674
Flash this example onto an nRF 52840
DEFMT_LOG=debug cargo run --release
If you get an error mentioning a more recent version of
cargo install probe-run
…for which, on linux, you may need
sudo dnf install rust-libudev-devel
If the app quits after a few seconds, try flashing the softdevice.
If you know your board’s UUID — look in its startup output — feed it
to the the
provision command. For example,
[mesh-cfgclient]# provision 066187E34A19B375F1A02A1E934DB15A
If you don’t have the UUID, you can discover it:
[mesh-cfgclient]# discover-unprovisioned on Unprovisioned scan started
Wait for it to discover your nRF broadcasting the "please provision me" packets. Once you see the board’s UUID, provision it.
[mesh-cfgclient]# discover-unprovisioned off [mesh-cfgclient]# provision 066187E34A19B375F1A02A1E934DB15A
If all goes well, you should see it assigning addresses and other happiness.
Right now, nothing you can really do other than taking note of the primary unicast address it assigned to your board, and then:
[mesh-cfgclient]# menu config [mesh-cfgclient]# target 00d9 Configuring node 00d9 [config: Target = 00d9]# beacon-get
Which should hopefully report back a
0x01 for the beacon-status.
If the packet gets lost, you’ll see a
no response type of output.
This is where we are currently.
If the packet goes lost, no retransmits of config stuff happens (yet) so just keep repeating it until you a response if you’ve successfully provisioned.
If the board complains about nRF Softdevice interrupts being disabled for too long, that’s because of the debug output using too much critical sections. You can reduce the log level or just try again.
If you want to start back from scratch, alter the
main.rs to use the
.force_reset() line (once) which will
factory-reset the board.
On the pi side, after
menu config and setting the
target to the board:
[config: Target = 00d9]# node-reset
This will remove it from the DB.
You can then
back and do the
discover-unprovisioned on and the
provision $UUID bits again.